Dear Trish:
This promises to be a good one!
“
I called the fabricator about it, who said that permanent water rings such as these are "normal" with granite
”
Okay then, which is the stone that etching is not normal with??... People chose granite and mercantile granite because, unlike marble, it does not etch – end of the debate. Even your stone, which is in reality alkaline feldspar syenite (does your fabricator know that? And if not, why doesn't he?) is never harmed by the typical household acidic substances. In other words, if that is what he told you, he's lying out of his teeth to get out of a kind of trouble that he knows nothing about.
“
I read on your site that because Emerald Pearl is such a dense stone that it should not have been sealed in the first place and that the water etches may be in the sealant, not in the stone
”
That is accurate. On top of the fact that the stone is naturally very dense, it was also allegedly resined by the factory (the application of epoxy), which makes it totally liquid-resistant. Only a total incompetent would have ever thought to apply an impregnator to a stone like that and resined to boot. Most likely is the invisible film of impregnator left behind that's etching. It is typical.
“
I don't know if the etches are in the epoxy resin either.
”
That is to be excluded. Epoxy resin does not etch.
“
Anyway, I am heartbroken about the etch marks. I am worried that I cannot put drinks on my counter for any length of time without getting these etches, which basically renders my brand new counters USELESS!!!
”
I feel for you. It's hard to believe that a customer with a stone as enjoyable as Emerald Pearl has to be in a situation like that just because some incompetent applied a sealer to it blindly believing that's granite and now he doesn't give a rat's behind about your problem, which he created and is fully responsible for.
“
I would really appreciate it if you could give me some ideas of how to get rid of the etch marks
”
Since the sealer is sensitive to acids, I would strip your countertop with a mild solution of water and phosphoric acid; or simply slowly rub your countertop, one section at a time, with white vinegar or lemon juice. (Always test on an inconspicuous part first, although there should not be any surprise.) That should do it.
“
AND most importantly, how to prevent them in the future.
”
Once the surface of your countertop is bare, the problem will automatically cease to exist effective immediately.
“
If you suggest removing the sealant, should this be professionally done -- should I insist that my fabricator do it
”
I already told you how to remove it, but it would be fun forcing your fabricator to do it! He wouldn't probably know where to begin!!!
“
is there any risk to the stone or the epoxy resin by removing the sealant?
”
No. But if the testing with the white vinegar (or whatever else) will show some problem, then you will insist to have the fabricator do it and face his responsibilities. Keep me posted if the test produces unsuitable results.
“
Stone Care International has suggested using their GD Dark Granite Polishing Powder for dark granite to remove the etches. It can be done by the homeowner. Is this a reasonable first step or a waste of time and $$?
”
What can I tell you? They would never give you any free advice unless they had a chance to sell you some of their stuff…
J
I have products like that, too, but they are complicated to use and could create problems. And, BTW, I don't sell vinegar or lemon juice…
L
Now remember, it's never too early to think about the proper maintenance of your stone. The issue of what you'll be doing day in and day out to your stone is – as it should be intuitive – vastly more important than its sealing
(if and when possible and/or advisable – which in your
And remember, every single penny of the cost of the literature will be used to support this site and its cause: your cause.
While you are in the “Helpful Hints” section, do spend some time reading all of the interesting FREE articles you'll find in there!
Finally, keep in mind that we need your support to help us helping you!
Will you please read and e-sign our Statement of Purpose at:
http://www.marblecleaning.org/purpose.htm?
By spreading the word about this valuable site among your friend & family and the stone trades' people you've been dealing with, you will be rendering everybody a valuable service!
Thank you
Ciao and good luck,
Mauri
Article ID: 1015
Created On: Tue, Jan 8, 2008 at 11:48 AM
Last Updated On: Tue, Jan 8, 2008 at 12:00 AM
Authored by: Maurizio Bertoli [mail@mbstone.com]
Online URL: https://marblecleaning.org/knowledgebase/article.php?id=1015